Milviz F4-E Phantom causes a P3D 4.5 crash [Answered]

Locked
Caribe
Posts: 53
Joined: Wed May 31, 2017 5:34 pm
Milviz F4-E Phantom causes a P3D 4.5 crash [Answered]

Post by Caribe » Tue Jun 07, 2022 5:48 pm

Hello Friends. I need help. I have reinstalled P3D 4.5 after my system crash. (Last 4.5 version incl. all hotfixes). Now I have also reinstalled all Milviz aircraft. The F4-E (latest Version 180712) causes a P3D crash. I get when I select the aircraft the cockpit only a few seconds to see. It comes the message P3D has detected an error and will be closed.
My question about this: Is there a so-called log file where it says what caused this CTD? Where can I find this file?

Regards
Julio Garcia

User avatar
Slayer
Posts: 1517
Joined: Sat Mar 08, 2014 3:26 am
Contact:
Re: Milviz F4-E Phantom causes a P3D 4.5 crash

Post by Slayer » Tue Jun 07, 2022 11:06 pm

Have you tried Windows event viewer? You should see something in there regarding P3D.

Specifically which version are you using because the install order is important if you have TP and ADV etc...

Caribe
Posts: 53
Joined: Wed May 31, 2017 5:34 pm
Re: Milviz F4-E Phantom causes a P3D 4.5 crash

Post by Caribe » Wed Jun 08, 2022 5:11 am

Thank you for the information. I also posted in Avsim forum about it. I would be recommended to install the latest wx radar version. One for P3D v4.5 HF3. Where can I find this version (link to download please)???
The F4-E I have installed version 180712. I also have following versions:

MV_F-4E_Phantom_II_ADV_vA1.180712_EADV
MV_F-4E_Phantom_II_TACPACK_vA1.180712_ETP
MV_F-4SJ_Phantom_II_TPADV_vA1.180712_JS

I think the last 3 here were the versions I had installed before my system crashed. What would be the sequence to install???

Regards
Julio Garcia

Caribe
Posts: 53
Joined: Wed May 31, 2017 5:34 pm
Re: Milviz F4-E Phantom causes a P3D 4.5 crash

Post by Caribe » Wed Jun 08, 2022 10:06 am

Other information: I am not a TAC-PACK user. Now I have tested something: The F4 in cold & dark mode does not crash at the beginning but the ACM panel remains gray. If I then try to start the phantom comes the CDT.

Caribe
Posts: 53
Joined: Wed May 31, 2017 5:34 pm
Re: Milviz F4-E Phantom causes a P3D 4.5 crash

Post by Caribe » Wed Jun 08, 2022 7:03 pm

I have found here in Forum following Info:

F-4E:
Base package->TACPACK package->ADV package

F-4J/S:
Base package->ADV/TACPACK package

Since I have these variants would that be feasible for me an installation in this sequence???

User avatar
Slayer
Posts: 1517
Joined: Sat Mar 08, 2014 3:26 am
Contact:
Re: Milviz F4-E Phantom causes a P3D 4.5 crash

Post by Slayer » Wed Jun 08, 2022 7:22 pm

The install order you listed there looks correct.

If you aren't a TP user then just skip over the part about installing it. Not sure the result if you install it and do not have TP installed.

I don't believe the WXR was used in this product.

Caribe
Posts: 53
Joined: Wed May 31, 2017 5:34 pm
Re: Milviz F4-E Phantom causes a P3D 4.5 crash

Post by Caribe » Wed Jun 08, 2022 7:57 pm

Thank you for the great support.

Regards.


Locked

Return to “McDonnell Douglas F-4 Phantom II Support Phorum”