KA350i Version 1.1.39 Beta (V4 + V5)

[michaelth]

2020-10-9_18-30-33-213.jpg (120.15 KiB) Viewed 565 times

Congratulations & thank you,

WX radar working in P3Dv5 with ActiveSky!

Michael

[Kdub]

Great! Still hangs my machine on version 5, works great on version 4.5.

Kdub

2020-10-9_18-30-33-213.jpg

Congratulations & thank you,

WX radar working in P3Dv5 with ActiveSky!

Michael

[michaelth]

Short flight from ESSD to ENRY (175nm) in Sweden: very well flying aircraft, good taxi speed control in beta range, FLC working both in climb and descent, captures ILS, and so on. Handling is a joy. Lots of fun in VR, especially looking left and right on the impressive engines.

Michael

[Slayer]

Just a quick note that this screen during installation is not interactable, it just automatically closes after a few seconds. May be intentional, but I want to only install into P3Dv5 and can't deselect v4.
Clipboard01.jpg

Correct, you are not able to select that , it is automated. Takes up very little space anyways on V4 and will not hurt anything, many MV products use it.

[michaelth]

There is a problem with FP load if there are more than two pages of flightplans: when trying to load the first FP of the third route page, the first plan of the first route page is addressed. When trying the second FP of the third route page, the second FP of the first page is loaded, and so on. In effect, you can load the contents of the first two route pages only.

23 flightplans are attached for testing.

Michael

[heightsmite]

I noted the same thing earlier in this thread. The flight plan selection after two pages is screwed up.

And, that MV_WXM.dll that was provided crashes my p3d to desktop.

STILL IN VERSION 4.5.2, clean install, radar does not work successfully.

[Kdub]

I noted the same thing earlier in this thread. The flight plan selection after two pages is screwed up.

And, that MV_WXM.dll that was provided crashes my p3d to desktop.

STILL IN VERSION 4.5.2, clean install, radar does not work successfully.

That's strange. In v5 just loading the aircraft crashes the sim for me. V 4.5 works fine.

Kdub

EDIT: I reverted to 1.1.38 and installed the weather .dll and everything works! No sim hang, no problem. Why?

[mxkuhn]

EDIT: I reverted to 1.1.38 and installed the weather .dll and everything works! No sim hang, no problem. Why?

The Download for 1.1.38 in the Support Forum does not work for me (Page Not Found). Is there a working link available for that legacy version?

Cheers

[Kdub]

EDIT: I reverted to 1.1.38 and installed the weather .dll and everything works! No sim hang, no problem. Why?

The Download for 1.1.38 in the Support Forum does not work for me (Page Not Found). Is there a working link available for that legacy version?

Cheers

I don’t think so. Maybe someone from Milviz can help us. Also, I just installed .39 with .38 still installed instead of deleting .38 first and now I have the brighter displays that aren’t in .38. When flying in cloud on Active Sky I couldn’t read the MFD with 1.1.38.
Now using 1.1.39 with no more hangs and with weather radar!

[Slayer]

You should always use the control panel to remove a previous beta version as the files and or names may not be in sync between versions so there could be conflicts. A .dll for the WXR is posted above.

[Kdub]

You should always use the control panel to remove a previous beta version as the files and or names may not be in sync between versions so there could be conflicts. A .dll for the WXR is posted above.

I did remove .38, but .39 crashes my PC! I mean when I load the King Air in P3Dv5, no matter how I do it, the sim crashes and my PC requires a cold reboot. So I reverted to .38 which worked fine, except when using Active Sky in clouds. The dim screens in the panel were unreadable. I then decided to install .39 over .38 just on a hope that I could get the brighter screens. It seems to be working fine!

Kdub

EDIT: I removed the KA and installed .39 per your directions. So far, with two (2) P3D loads, I haven't had a crash! I don't understand what went wrong before...

[heightsmite]

You should always use the control panel to remove a previous beta version as the files and or names may not be in sync between versions so there could be conflicts. [

b]A .dll for the WXR is posted above[/b].

That .dll crashes my p3d 4.5.2 as soon as the radar is turned on.

[Slayer]

You should always use the control panel to remove a previous beta version as the files and or names may not be in sync between versions so there could be conflicts. [

b]A .dll for the WXR is posted above[/b].

That .dll crashes my p3d 4.5.2 as soon as the radar is turned on.

That's because that .dll is for V5. They are not interchangeable. I suspect you have a different problem in v4

[scottgridley]

Just a quick note, FPS seems really nice with 1.1.39 for me in P3Dv5. THANKS! I am still having issues importing simbrief tfdi flight plans into the FMC from the \Prepar3D v5\Milviz\FMS-3000\Routes folder. Is that functional at this time? Maybe a different format besides tfdi 717?

Flew from Orbx KPSP with true earth scenery and voxatc AI at 95% with smooth frames the whole way!

Prepar3D Screenshot 2020.10.13 - 20.16.50.24.jpg (290.09 KiB) Viewed 424 times

[ferrariman15]

I don't know whether this is a bug or something I am doing wrong but on the Collins FMS 3000 when I input my departure airport and then my destination airport on the flight plan page the distance stays at zero. Every video I have watched on the FMS 3000 as soon as you enter your departure and destination airfields the distance between the two should be displayed even before inputting the rest of your flight plan. Unless I am doing something wrong that is.