Update Problem
-
- Posts: 45
- Joined: Sat May 25, 2013 5:59 pm
- Location: New Mexico, USA
Update Problem
I received an email about an update and downloaded MilViz_DHC-2_Beaver_v1.170526.zip. I ran as an uninstall first, then installed.
Now, when I go to Milviz MVAMS and select the Beaver I get a message saying "UPDATE AVAILABLE". If I click yes to install it says it is downloading for about a second, then I get a strange message box with {#} OMG GUID 3 - x as a header, and a message that says " Here, have a GUID. OMG GUID!
Any choice just results in no changes, bring up the UPDATE notice each time.
Can someone please explain / solve.
Thank you.
Joe L.
Now, when I go to Milviz MVAMS and select the Beaver I get a message saying "UPDATE AVAILABLE". If I click yes to install it says it is downloading for about a second, then I get a strange message box with {#} OMG GUID 3 - x as a header, and a message that says " Here, have a GUID. OMG GUID!
Any choice just results in no changes, bring up the UPDATE notice each time.
Can someone please explain / solve.
Thank you.
Joe L.
- Attachments
-
- Untitled.jpg (26.43 KiB) Viewed 635 times
-
- Posts: 63
- Joined: Tue May 24, 2011 9:37 pm
- Location: Wichita Falls, Texas, USA
Re: Update Problem
Got it as well myself. I just closed the box and continued on.
-
- Posts: 13
- Joined: Sun Nov 11, 2012 2:56 am
- Location: CYYC
Re: Update Problem
Hmmm,
I just ran the update over the original install without un-installing and did not get this message. Then again perhaps I borked my install and just don't know it yet. There was no read me file to indicate whether we were to un-install the original or not so I just ran the update over top with no issue I can see thus far. Perhaps you can try the same, assuming you have the original installation file.
Cheers,
Thad
I just ran the update over the original install without un-installing and did not get this message. Then again perhaps I borked my install and just don't know it yet. There was no read me file to indicate whether we were to un-install the original or not so I just ran the update over top with no issue I can see thus far. Perhaps you can try the same, assuming you have the original installation file.
Cheers,
Thad
-
- Posts: 47
- Joined: Mon Oct 19, 2015 8:42 pm
Re: Update Problem
i have the same problem.i launch Milviz MVAMS i got a message saying an update is available. i click yes and i have this GUID window.
and nothing is updated if i close this window.
(occurs after isntalling Beaver update)
this mesage is displayed by the downloaded (in C:\Users\myuser\AppData\Local\MVAMS\Downloads) DHC2.exe file
if i click on it, i have the same message)
regards.
and nothing is updated if i close this window.
(occurs after isntalling Beaver update)
this mesage is displayed by the downloaded (in C:\Users\myuser\AppData\Local\MVAMS\Downloads) DHC2.exe file
if i click on it, i have the same message)
regards.
-
- Posts: 94
- Joined: Fri Mar 03, 2017 2:03 pm
Re: Update Problem
Same issue - I uninstalled the old version, installed the new version, and now I get the update message and this popup if I select yes.
-
- Site Admin
- Posts: 1728
- Joined: Mon Sep 08, 2008 4:18 pm
Re: Update Problem
We are aware of this and are prepping a new installer
-
- Posts: 442
- Joined: Mon Dec 20, 2010 4:30 pm
Re: Update Problem
Gentlemen, A quick fix to the issue while the updater is under scrutiny.
Go to > AppData\Local\MVAMS\Versions\DHC2 < and delete the > DHC2 < folder .
Alternatively , click No when asked to update .
Our Abject Apologies for this error , its being rectified in the least possible delay
Go to > AppData\Local\MVAMS\Versions\DHC2 < and delete the > DHC2 < folder .
Alternatively , click No when asked to update .
Our Abject Apologies for this error , its being rectified in the least possible delay