KA350i saitek panels
-
- Posts: 6
- Joined: Fri Mar 20, 2020 7:42 pm
KA350i saitek panels
Hi
I bought the KA350i recently. It's a nice model. But I'm a little disappointed.
I have saitek equipment : switch panel, radio panel, multi panel, and FIP.
Few things work with the 350i. Almost nothing. It's really too bad.
Is there a solution?
Maybe I doing it wrong.
Thank you
I bought the KA350i recently. It's a nice model. But I'm a little disappointed.
I have saitek equipment : switch panel, radio panel, multi panel, and FIP.
Few things work with the 350i. Almost nothing. It's really too bad.
Is there a solution?
Maybe I doing it wrong.
Thank you
-
- Posts: 122
- Joined: Sun Oct 28, 2012 2:01 pm
- Location: MV Beta TEAM
- Contact:
Re: KA350i saitek panels
Check SPAD.next and FIP Gauges. Both works great with MV addons.
Default drivers are buggy and dont work with all addons.
Default drivers are buggy and dont work with all addons.
-
- Posts: 411
- Joined: Wed Feb 26, 2014 3:07 am
Re: KA350i saitek panels
Did you try setting them up in MVAMS controls tab? I will also advise you use the Official Support forum. Send an email to Oisin for access
-
- Posts: 6
- Joined: Fri Mar 20, 2020 7:42 pm
Re: KA350i saitek panels
@yoyo
Thank you for the answer.
I know spadnext. I don't use it because it's too complicated. I prefer SPAD, the first software. It works very well with my other planes.
I've found that the standard keyboard shortcuts don't work. For example: shift+M for the battery doesn't work.
Switch panel, dont'work : all buttons except pitot, strobe and landing lights.
Multi panel, don't work : autopilots buttons (A/P, HGD, NAV....), it's possible to change curse but no heading, trim.
Radio panel : com OK, Nav OK,
Have you tried with SpadNext?
@Raptor
Thank you.
I didn't see MVAMS control tab. Only three tabs : Load, Options and Visuals
Thank you for the answer.
I know spadnext. I don't use it because it's too complicated. I prefer SPAD, the first software. It works very well with my other planes.
I've found that the standard keyboard shortcuts don't work. For example: shift+M for the battery doesn't work.
Switch panel, dont'work : all buttons except pitot, strobe and landing lights.
Multi panel, don't work : autopilots buttons (A/P, HGD, NAV....), it's possible to change curse but no heading, trim.
Radio panel : com OK, Nav OK,
Have you tried with SpadNext?
@Raptor
Thank you.
I didn't see MVAMS control tab. Only three tabs : Load, Options and Visuals
- doodlebug
- Posts: 1642
- Joined: Sun Feb 19, 2017 2:49 pm
- Location: LYX>YUL
-
- Posts: 6
- Joined: Fri Mar 20, 2020 7:42 pm
Re: KA350i saitek panels
Thank you!
I downloaded and installed the Hot Fix 1.0.6.
Unfortunately, it hasn't changed anything.
I don't understand why I don't have the checkbox "Enable hardware mapping" with contols tab
I downloaded and installed the Hot Fix 1.0.6.
Unfortunately, it hasn't changed anything.
I don't understand why I don't have the checkbox "Enable hardware mapping" with contols tab
- doodlebug
- Posts: 1642
- Joined: Sun Feb 19, 2017 2:49 pm
- Location: LYX>YUL
Re: KA350i saitek panels
Do you see this page?
When you installed the hotfix did you get the screen that prompts to modify, repair or uninstall the MVAMS?
When you installed the hotfix did you get the screen that prompts to modify, repair or uninstall the MVAMS?
-
- Posts: 6
- Joined: Fri Mar 20, 2020 7:42 pm
Re: KA350i saitek panels
Yes I see this page and I see controls tab.
But in this tab i don't see the checkbox. I don't.
When I installed the hotfix I got the screen that prompts to repair, modify or uninstall. I have chosen repair.
But in this tab i don't see the checkbox. I don't.
When I installed the hotfix I got the screen that prompts to repair, modify or uninstall. I have chosen repair.
-
- Posts: 6
- Joined: Fri Mar 20, 2020 7:42 pm
Re: KA350i saitek panels
I installed the new version 1.1. A lot of bugs have been fixed, it's great, thank you. But I still have the same issu : the saitek panels don't work correctly.